The Content Of The Article:

Realize the restoration of a varnished piece of furniture

This pedestal mahogany varnished, Napoleon III style, will require a restoration in several stages: re-bonding the broken foot, replacing and stripping decorative copper fittings, refurbishing the varnish and stain removal of marble constituting the plateau. These operations will give rise to the use of several "tricks", well known to those skilled in the art.

Necessary material

  • Fine brush
  • Cotton swab
  • Tape
  • Masking tape
  • Lemon
  • Wood glue
  • Lint-free cloth
  • deoxidizer
  • mess
  • Cotton or cotton fabric
  • Stick wax
  • White wax

Steps

  1. To pick up the broken foot of a pedestal table
  2. Repositioning and stripping copper decorative fittings
  3. Refurbishment of the varnish
  4. Detach marble

To pick up the broken foot of a pedestal table

Glue the adjoining part to the pedestal table

Glue the adjoining part to the pedestal table

1. The first operation will consist of gluing the broken foot. The wood is not stringy, the case is clear and frank. Check that it is not an old break, because in this case, all traces of dried glue should be removed before the repair can be done. First glue the adjoining part to the pedestal table with wood glue.

Glue the foot

Glue the foot

2. Then clean if necessary the break on the detached part of the foot and spread the wood glue.

Assemble both sides and press firmly

Assemble both sides and press firmly

3. Although it is not a contact adhesive, wait a few minutes then apply both sides to assemble against each other and press hard. The fact that the glue is at the beginning of the drying phase gives it a better adhesion. In the case of furniture having to withstand heavy loads, it will be necessary to provide for the introduction of a trunnion which will strengthen the assembly.

Laying an adhesive tape on the two glued pieces

Laying an adhesive tape on the two glued pieces

4. Immediately remove any glue dripping before firmly holding both sides of the pedestal table. In our example, we used tape to bond the two parts of the foot. Apply strong pressure when applying tape.

Repositioning and stripping copper decorative fittings

To pick up a fitting

To pick up a fitting

1. The support columns of this pedestal table include grooves, in which take place fittings, one of which, poorly fixed, requires a partial re-bonding. Always clean traces of glue before they dry.

Keep the hardware glued with tape

Keep the hardware glued with tape

2. Insert the glue under the fitting and hold it tight, time of drying, with adhesive tape.

Paste copper and throat

Paste copper and throat

3. To put back this copper element, we used the same glue as before. A little trick: to make it easier to take the glue on the copper, first put a clove of garlic on it.

Arrange strips of masking tape over the varnished parts

Arrange strips of masking tape over the varnished parts

4. Wait until the glue is dry before stripping the copper. Before starting this operation, you must protect the wooden parts. To do this, lay the strips of masking tape on all the varnished parts nearby.

Apply a cleaner

Apply a cleaner

5. Spread the cleaner with a paintbrush, leave on for a few seconds and wipe with a dry, lint-free cloth.

Cover metal parts with hard wax

Cover metal parts with hard wax

6. Given the complexity of the pattern of these fittings, it was not possible to adequately protect the varnish with the masking tape. We covered the metal parts with hard wax. Know that you can also use candle. Work carefully so as not to overflow the hardware.

Pass a deoxidant

Pass a deoxidant

7. After eliminating the wax that may have spilled over the fitting and that would hinder the effectiveness of the product on the copper, pass the deoxidizer with a small fine brush without loading it too much so as not to cause unwanted sagging.

Pour water on the fittings to remove stripper streaks

Pour water on the fittings to remove stripper streaks

8. All these finished interventions, pass water on the fittings in order to remove all traces of stripper and stop its action. Wipe immediately.

Refurbishment of the varnish

Fold in two a strip of cotton fabric

Fold in two a strip of cotton fabric

1. In order to treat all the wooden parts of the pedestal, you will need a cotton pad. For this, you can use cotton to melt, otherwise here is a simple way to make a stamp. Take a strip of cotton fabric and fold it in half.

Roll the tape tightly

Roll the tape tightly

2. Then roll this folded tape tight enough.

Surround the elastic cotton

Surround the elastic cotton

3. You will keep it rolled by rubber bands.

Apply some food on the cotton

Apply some food on the cotton

4. This stamp is not one of those traditionally used by cabinetmakers; however, it is perfectly suited to the application of "popote"...

Revive the nail polish with cotton

Revive the nail polish with cotton

5.... which aims to revive the nail polish. Apply the product by holding the pad in its length and slightly rotating it.

Wipe up the excess food with a rag

Wipe up the excess food with a rag

6. Spread the product well and have it penetrate in concentric circles. Then wipe with a cloth to remove any excess.

Detach marble

Rub the tray with half a lemon

Rub the tray with half a lemon

1. All you have to do is take care of the board. To remove the superficial stains on marble, here's a little trick: rub the tray with half a lemon.

To pass a layer of encaustic colorless marble

To pass a layer of encaustic colorless marble

2. Emphasize the tasks then, after wiping the tray, pass a thin layer of special colorless polish (preferably liquid and hot) that will give the marble its brilliance.

Restored pedestal

Restored pedestal

3. Your pedestal has regained its luster and can once again find its place in your home.

Realize the restoration of a varnished piece of furniture: restoration

On the same topic

  • Questions answers
    • How to protect the tray of a wooden table?
    • How to solve a problem of scratches on a piece of furniture?
    • Why does not my buff varnish dry?
    • Kitchen furniture that is aging too fast
  • DIY tips
    • Renovate an old frame
    • Restore yourself a rustic chair pierced
    • Restoring a Louis XIII style chair
    • Successfully restore a wooden table
    • How to restore a wooden door panel?
    • Restoration of an antique furniture
    • Buffer varnish

This may interest you


Video Instruction: How To Paint & Refinish Furniture without Sanding | On A Budget | For Beginners | DIY | Rust-Oleum