The Content Of The Article:

On an old wood floor that has hollows and badly joined blades I would like to know if the patching and the primer to use as well as the product for the joints of the blades in order to level the ground to then apply insulation and laminate flooring.

Beforehand, measure the differences in level and flatness of your floor. Smoothing is only possible if they are not greater than 5 mm. Beyond that, you have to either look at the floor itself or pour a lighter concrete screed if the joist allows it. Re-seal small cracks and cracks between boards with woodpulp to prevent leakage. Seal the larger slots with packing string or papier mâché. Remove any nails protruding with the pincers or chase out the protruding ones. Reattach the lifting blades with new nails. Wash the floor and allow to dry before applying a "special leveling" primer.

Do not hesitate to consult our sheet CONCRETE SOIL FLOORING AND PARQUETS.

On the same topic

  • Questions answers
    • How to close the slots of a wooden floor?

This may interest you

Patching a parquet floor

FAQ - 💬

❓ Can you patch parquet flooring?

👉 Fixing Loose Parquet Blocks The most common solution for loose parquet is to remove the affected blocks, and clean off old adhesive, before fixing them back into place using a suitable flexible floor adhesive.

❓ How do you repair a hole in a parquet floor?

👉 Find a wood filler that matches the color of your hardwood floor then use a putty knife to put the putty into the hole a little bit at a time. Press down to make sure you fill the hole completely. make sure to read the manufacturer's instructions to see how long to wait for the putty to dry thoroughly.

❓ How do I fix a deep scratch in my parquet floor?

👉 0:593:003 DIY Ways to Fix a Scratch in Hardwood FloorsStart of suggested clipEnd of suggested clipBuff the scratch. And surrounding area to blend it in for a large scratch or chip in the flooring.MoreBuff the scratch. And surrounding area to blend it in for a large scratch or chip in the flooring. You'll likely need a stainable wood filler a stain pen or stain matching your floor.

❓ How many times can a parquet floor be sanded?

👉 If needed, you should be able to sand your Pergo wood floor 2 – 3 times depending on which quality you installed. A general rule is that you can sand one time for each mm of the top-layer thickness, but this depends on sanding method.

❓ Is parquet glued down?

👉 Gluing down the parquet tiles is the most crucial part of the installation process. Since the pattern is geometrical, a piece of flooring installed at the wrong angle can throw off the appearance of the whole floor. You can glue parquet floors down on either a plywood or a concrete subfloor.

❓ How do you restore parquet flooring without sanding?

👉 You can apply two coats of the hard wax case the wear and tear of the parquet floor are heavier. The process of applying such products on top of the existing finish of the floor is named recoating and does not require further sanding and refinishing.

❓ Why do people not like parquet floors?

👉 It does not take much for your precious parquet floors to be scratched by a small, sharp object, and once it is scratched, repairing the floor can be difficult and expensive. Stilettos should never be worn on parquet floors because the pressure from walking on them is more than enough to cause scratches.

❓ Are parquet floors real wood?

👉 Parquet is a type of wood flooring made by arranging small slats of wood in distinct, repeating patterns. While traditional parquet floors were installed one piece at a time, most modern parquet comes in tile form in which the wood slats are bonded to a backing material.

❓ Can deep scratches in a wood floor be repaired?

👉 For deeper or wider scratches, take a putty knife and apply wood filler into the crack, wiping off excess while still wet. Sand down dried wood filler with 180-grit sandpaper, avoiding the surrounding floor. Apply matching colorant to wood filler, also.

❓ How do you fix gouges dents and deep scratches in hardwood floors?

👉 You can use abrasion with a fine steel wool pad to gently repair scratches that haven't pierced the finish. Buffing or polishing may also help erase surface-level marks on your floors. For repairing deeper dents and scratches in hardwood floors, you can use wood putty to fill in the gouges.

❓ Should I fill gaps in parquet floor?

👉 When sanding or sealing parquet flooring, you need to know that it is important to fill in any large or small gaps in between the blocks. A parquet floor, which is laid accurately does not need any gap filling.

❓ How do you fix loose parquet flooring?

👉 The most common solution for loose parquet is to remove the affected blocks, and clean off old adhesive, before fixing them back into place using a suitable flexible floor adhesive.

❓ Can You varnish parquet flooring?

👉 When sanding and buffing is complete, you can apply a finish to your parquet floor. Don't attempt to do this until the floor is thoroughly clean — brush, then hoover the floor and wipe it down. You can use wax, oil or a varnish (also known as lacquer) to seal and protect your floor.

❓ What is parquet flooring restoration?

👉 For many, restoring parquet flooring is a way of bringing the character and charm of its period flooding back-here, we explain how to restore parquet floors.

❓ How do I prepare a parquet floor for installation?

👉 Replacing missing or damaged parquet blocks. Re affixing any loose blocks. Renewing substrate and under floor leveling. Fireplace and other concreted areas removed and prepared for blocks laying. Gap filling of the parquet floor. Supplying full aftercare information. Complete installation of parquet floors. Lacquer or Oil wax finish?


Video Instruction: DIY HOW TO REPAIR A WARPED PARQUET FLOOR