The Content Of The Article:

Is it possible to redistribute the heat emitted by a stove into the room above the one where the heater is installed? Can it be done without installing formwork around the flue pipe?

One of the solutions to redistribute the heat emitted by a stove is to install on the upper floor a non-insulated duct and to surround it with a decorative wire mesh, of expanded metal type, in order to take advantage of the exchanges of heat without risking to be burned.
There are also devices for recovering calories from stoves and inserts or closed hearths in the form of motorized boxes for heat exchange and hot air distribution in other rooms of the house. The systems developed by Poujoulat are, for example, very efficient.

On the same topic

  • Questions answers
    • How to diffuse the heat emitted by a pellet stove?
    • Tips for installing, renovating, maintaining... a chimney
    • How to improve the diffusion of heat in a house?
    • Install a heat pump and a wood stove
    • How to distribute the heat of a closed fireplace in several rooms?
    • Installation of a wood or pellet stove
  • DIY tips
    • How to install a wood stove?

This may interest you

How to recover the heat emitted by a wood stove?

FAQ - 💬

❓ How do you make a heat reclaimer?

👉 0:002:28DIY Chimney Heat Reclaimer For Wood Burning StoveStart of suggested clipEnd of suggested clipSection two caps a blower and two t's and we also need a power cord we'll trace the six inch pipe onMoreSection two caps a blower and two t's and we also need a power cord we'll trace the six inch pipe on the cap. And cut it out with an angle grinder.

❓ How do I circulate the heat from my wood stove?

👉 0:415:24Tips On Moving Heat From The Wood Stove To The Hard To Reach PlacesYouTubeStart of suggested clipEnd of suggested clipSo one thing that we have found that makes a several degree difference for us is distributing. TheMoreSo one thing that we have found that makes a several degree difference for us is distributing. The air one by setting a fan really low to the ground. And then blowing it in the direction.

❓ How can I make my wood burning stove more efficient?

👉 Here are our top tips to improve the efficiency of your wood stove:

  1. Get the chimney right. ...
  2. Keep the chimney clean. ...
  3. Think about positioning. ...
  4. Use dry wood. ...
  5. Use the 'top down' lighting method. ...
  6. Wait, don't just throw on logs. ...
  7. Make sure it's cold outside, or warmer inside.

❓ What is a heat reclaimer for wood stoves?

👉 This heat reclaimer can save on heating bills and can be easily installed in the flue of any air-tight wood stove or freestanding fireplace. How it works is the exhaust heat and gases travel upward through the flue, circulating around the heat-exchanger tubes.

❓ How do you make a heat exchanger?

👉 0:055:51Homemade "Copper & Steel" Heat Exchanger! -for heating (& cooling ...YouTube

❓ What is a fireplace heat exchanger?

👉 Fireplace Heaters are a heat exchangers that sit on the floor of your fireplace and were designed to boost the convection heat produced by your fireplace. The Fireplace Heater draws in the cool air from your living space, circulates it through the hot tubes and then pushes the heated air back into your room.

❓ Should I put a fan behind my wood stove?

👉 Without a stove fan, you are in danger of wasting a lot of the warm air produced from your wood burning or multi-fuel stove. Due to the fact that hot air rises naturally, you may find that the room with your wood burning stove is cooler than those above it, which is the exact opposite of what you want!

❓ Can you add a blower to a wood stove?

👉 Yes, you can add a fan/blower to most gas and wood fireplaces, inserts, and stoves. You will need to find a fireplace rated fan that will fit your fireplace and follow all instructions for installation in the unit's manual.

❓ How often should you add wood to a wood stove?

👉 During the process, wood must only be added when the fire is beginning to smolder. This situation could be anytime between 4-6 hours, depending on the wood you use.

❓ Can you put too much wood in a wood stove?

👉 Manufacturers of wood burning stoves recommended to only have a certain amount of wood in the stove at one time. Placing too much wood into a stove or allowing too much air flow to the fire can cause the stove to over fire.

❓ How does the miracle heat reclaimer work?

👉 The "Miracle Heat" Heat Reclaimer is designed to utilize a part of that lost heat, and yet let enough heat pass through the chimney to maintain proper draft and temperature so that creosote and soot formation is kept to a minimum.

❓ How do you keep a wood stove from overheating?

👉 Use Fans. Using fans to move the heat around will allow you to heat the entire upstairs, or place fans that move the wood stove heat to only one room.

❓ What happens when you recoheat a gas stove?

👉 Vast amounts of heat energy escapes through your stove’s chimney. Recoheat recovers some of the lost heat and returns it into your home, pumping it out at a flow rate that doubles for every 238°C increase in heat, because the air expands as it heats.

❓ How do I increase the heat from my wood burner?

👉 Transform the heat output from your wood burner or solid fuel stove by installing a Recoheat heat recovery unit into the bottom of your flue. The heat exchange unit recovers an extra 1kw of heat from the flue, starts pumping it as soon as the fire is lit, and continues pumping it for hours after you stop refuelling and the stove cools.

❓ How much heat does a wood burning stove produce?

👉 With a small, hot fire in your wood burning stove, you'll be pumping out more than 7000 litres of air an hour heated to 500°C using our standard air pump. Check out our How it works page for the details, and come and reclaim the heat from the heart of your stove to warm the heart of your home.


Video Instruction: Light from Waste Heat