The Content Of The Article:

Renovation of an old chair

This old chair Louis XIII style, requires intervention on several levels: some carpentry repairs, wood treatment and protection, repair of the tapestry. First, remove the fabric covering the seat. This operation must be done with care. It is indeed important not to tear it, so that it can serve as a boss for the dressing of the seat.

Necessary material

  • pliers
  • Breast strap
  • Hammer end
  • Screwdriver
  • Clamp
  • Cutter
  • Gloves
  • Abrasive paper
  • Paint brushes
  • Chalk
  • Scissors
  • Treatment product
  • Wood glue
  • Lint-free cloth
  • Stripper
  • Brightener
  • Wood dough
  • Cabinet varnish

Steps

  1. How to strip the old filling?
  2. Make repairs with wood glue
  3. How to stretch and reclame the strap?
  4. Strip the wooden parts of the chair
  5. How to close the holes with the wood pulp?
  6. To varnish the wood, to cover the chair

How to strip the old filling?

Remove the nails.

Remove the nails

1. It is necessary first remove the nails using a pair of pliers. If they are old nails, that one wishes to preserve, bring oneself rather with a little crowbar.

Remove the fabric from the seat and backrest.

Remove the fabric from the seat and backrest

2. Then remove the fabric covering the seat and backrest. As already mentioned, work carefully so as not to damage the chair, he must then serve as a boss.

Dust the canvas.

Dust off the canvas

3. With a vacuum cleaner, carefully dust off the white canvas under the tapestry.

Make repairs with wood glue

Glue dripping.

Glue dripping

1. All components of the chair must be checked.
In this case, a slit seriously threatened the strength of the foot. Use the blade of a screwdriver to pry, spread the two parts of the foot slightly, then fill the slot with wood glue. Be careful not to enlarge the slot, immediately clean the glue drips.

Remove the clamp.

Remove the clamp

2. In order for the bonding to be effective and durable, maintain the repair area with a clamp. Also protect the foot of the chair, interposing two shims roughly curved profile.
Once the glue is completely dry, remove the clamp.

Compress the seat springs.

Compress seat springs

3. Flip the chair over, place a wedge to compress the seat springs.

How to stretch and reclame the strap?

Pull the strap.

Pull the strap

1. The method described below allows to restore the tension to the straps which will then have to be reclunk. A breast strap It is necessary to do this work because it keeps the strap in position while you nail it.

Reclose the canvas.

Reclose the canvas

2. Reclose the canvas to retension, because it is she who gives shape to the seat of the chair. If it is found that it can not resist this tension, replace it.

Strip the wooden parts of the chair

Strip the wood.

Strip the wood

1. Apply stripper on all wooden parts, feet and backrest.

Moldings and details of the sculptures.

Moldings and details of the sculptures

2. Insist in particular on the turned moldings and in the detail of the sculptures. Soak the cloth in moderation, so that the cleaner does not run on the fabric.

Apply the lightener.

Apply the lightener

3. Apply the lightener, which must be neutralized after a while with stripper. For this application, work with a brush and wear gloves to avoid contact with the product.

How to close the holes with the wood pulp?

Wood paste.

Wood dough

1. Examine the chair in detail, and cover all holes and imperfections with tinted wood pulp.

Fine sandpaper.

Fine sandpaper

2. Allow to dry. As the product tends to shrink on drying, it may be necessary to apply an additional layer.
Once dry and hard, sand the surplus wood pulp with a fine abrasive paper, then equalize all surfaces, remove all traces of stripper.

Wood treatment product.

Wood treatment product

3. Treat the wood even if it does not appear to be attacked. Paint on all the wooden parts.
Nevertheless, if a large number of small holes are revealed, inject the treatment product with an aerosol can with a needle-shaped tip.

To varnish the wood, to cover the chair

To varnish the wood.

Varnish the wood

1. The wood can now be varnished. We use a tinted cabinetry varnish, applied with a simple brush.

Deploy the old trim.

Deploy the old trim

2. Regarding the upholstery, lay the old upholstery flat on the new fabric that will cover the chair.

Post outlines with chalk.

Post contours with chalk

3. Post contours with chalk.

Cutting the fabric.

Cutting the fabric

4. Cut the new fabric according to the chalk line drawn from the old one.

Cover fabric.

Cover fabric

5. Position the cover fabric over the seat and backrest and begin driving the nails.

Nail the fabric.

Nail the fabric

6. When you are sure of the positioning of the fabric, continue studding, while being careful to recreate the bellows at the corners of the seat.

Cut the excess fabric.

Cut the excess fabric

7. It remains to cut the surplus fabric, by straightening with a cutter.

Louis XIII chair.

Louis XIII chair

8. This Louis XIII chair has regained its original luster. The green velvet is well worth the warm tones of the varnish, whose role is to cover and protect the wood.

Tutorial: How to restore an old chair: chair

On the same topic

  • Questions answers
    • How to replace the mulching of a chair?
    • Replace with fabric a seat of straw seat
    • How to enforce an oral commitment of a construction contract?
  • DIY tips
    • Rehabilitation of an old chair
    • Restore yourself a rustic chair pierced
    • Tutorial: How to restore a varnished piece of furniture
    • Successfully restore a wooden table
    • How to restore a wooden door panel?
    • Restoration of an antique furniture
    • Renovation of a leather chair

This may interest you


Video Instruction: Repair / Restore Leather Tufted Wingback Chair Tutorial